A pipe that splits inside a wall or ceiling turns into a flood in minutes, not hours. Shut the main, then call Water Heater Repairer and a live dispatcher will route you to an independent, licensed and insured plumber near you, plus a water damage contractor if the mess calls for one.
A burst pipe is two jobs at once: stopping the leak and dealing with the water it already dumped. We coordinate both so you are not juggling separate calls while the ceiling sags.
Repairs to supply lines fall under plumbing code, which is why we route only to licensed, insured independent plumbers. Feel free to ask for their license at the door and verify it yourself.
A spraying line inside a finished wall gets priority over a slow drip under a sink. Arrival is often quick, depending on your location and how many freeze calls are stacked up that night.
You get a written, flat-rate quote for the repair and any wall access before anything gets cut. No surprise line items once the wall is open.
Plenty of the plumbers we route to bring acoustic listening gear and a thermal camera. That narrows the break down to inches instead of tearing out a whole wall to hunt for it.
Freeze breaks, corroded galvanized runs, cracked CPVC fittings, and slab leaks all come through this line. Tell the dispatcher what the pipe looks like and where it runs, and we match you with someone who works on that material every week.
Once water has run into ceilings, insulation, or flooring, the pipe repair alone does not end the problem. A drying contractor with moisture meters, air movers, and dehumidifiers can be sent so the cavity dries out before the wall is patched. Sealing up a damp cavity is the fastest way to end up with a mold problem by spring.
Pipe material, location, and the reason it broke decide which repair makes sense.
Lines in exterior walls, crawlspaces, and unheated attics freeze first. Ice expands, pressure builds between the blockage and a closed faucet, and the pipe splits lengthwise, often hours later when it thaws.
Thin-wall Type M copper splits and pins faster than heavier Type L. The fix is cutting back to clean pipe and joining it with a sweated or press fitting.
PEX rarely splits, but crimp and expansion fittings can blow off when water freezes inside them. CPVC turns brittle with age and heat, and old fittings crack if you so much as bump them.
A warm patch on tile or a water meter still moving with everything off usually means the leak is under the slab. Acoustic detection and thermal imaging pin it down, then you weigh a spot repair against a reroute through walls or attic.
Old galvanized pipe corrodes from inside out, and the threads are usually where it gives up. Patching one section of a rotted run often just moves the leak a few feet down the line.
Braided supply lines under sinks and toilets burst without warning, and they run at full house pressure. A relief valve on the water heater that drips or dumps water needs a look too.
The process is short, and a real person handles each part.
We walk you through finding the main shutoff and killing power to any wet circuits. Then we ask what the pipe is made of, where it runs, and whether a ceiling is bulging.
We route the job to a nearby licensed plumber who carries stock for copper, PEX, and CPVC repairs. If water spread past the leak area, a water damage contractor can be scheduled right behind them.
The plumber traces the break, often with a thermal camera or acoustic detector, and checks the run for other weak spots. A written, flat-rate quote comes before any drywall is cut.
The permanent repair goes in, the line is pressure tested, and the plumber watches the joint under full pressure before closing anything up. Ask about the contractor's own written workmanship warranty before they leave.
A push-to-connect coupling can stop a spraying line in minutes, which makes it a solid emergency patch. Many plumbers still prefer a sweated or press fitting behind drywall, since that joint will sit unseen for decades.
Shut the main and call. We will get a licensed plumber moving your way.
The line in the laundry room's outside wall froze and split the first really cold night. The dispatcher talked me through finding the main, and the plumber replaced the split copper that same morning. He even pointed out that it was thin Type M and why that mattered.
Our water bill doubled and the hallway tile felt warm. They found the hot line leaking under the slab with an acoustic detector and a heat camera. We got two written prices, spot repair or reroute, and he explained both without pushing.
Water came through the dining room ceiling from an upstairs bathroom supply line. One call got me a plumber for the line and a separate drying contractor for the ceiling and carpet. Having both lined up from one call saved me a long night of searching.
I manage a small rental, and a tenant called about a CPVC elbow that cracked under the kitchen sink. The plumber replaced it, then showed me two more fittings that crumbled when he touched them. He quoted a full repipe of that wall in writing and did not pressure me to do it that day.
Close the main shutoff right away and kill power to wet areas at the panel. Open a lower faucet to drain the lines, move valuables, and call so a plumber can head your way.
Turn on the connected faucet and apply gentle heat with a hair dryer or a space heater nearby. Skip the torch entirely, because open flame starts wall fires and can burst the pipe with steam.
They are code-approved in many places, yet a lot of plumbers prefer them only where they stay accessible. Ask the plumber whether a sweated or press fitting makes more sense before the drywall goes back.
Listening equipment hears the leak, and a thermal camera maps the wet area through the drywall. That combination typically keeps the cut small and easy to patch later.
One leak on otherwise healthy pipe is usually a good case for a spot repair. Repeated leaks or aging copper tend to point toward a reroute so you are not breaking concrete again next year.
Let faucets on outside walls drip on hard freeze nights and open the sink cabinets so warm air reaches the pipes. Insulate exposed runs and add heat tape where pipes pass through cold crawlspaces, starting with the spots the plumber flags.
Calls go to independent plumbers covering South Beach, from older homes with galvanized pipe to new construction running PEX. Nearby suburbs are covered too, along with zip codes such as 32963.
Older homes near the center of town tend to have galvanized mains and thin copper branch lines, which is where pinhole leaks and corroded threads show up. Newer subdivisions lean on PEX and CPVC, where freeze-popped fittings and brittle elbows are the usual story. Wherever you are, tell the dispatcher the age of the house and we match the plumber to the pipe.
Frozen crawlspace pipes, attic runs, and slab leaks across older and newer houses.
Leaks that cross into a neighbor's unit, where fast shutoff and documentation both matter.
Surrounding towns around South Beach are covered by the same network.
